The Remington Model Four autoloading rifle was introduced by Remington Arms and was based on the company’s previous model, the Model 7400. The Model Four has a more refined action and a more secure lockup than previous iterations of this semiautomatic gas-operated action rifle.
Nevertheless, there are still many concerns and difficulties to be found.The most typical problems with this model are jamming, failing to feed, failing to eject, the bolt not locking, and failing to re-Cock etc.
If you want to learn the specifics of the problems and the approaches taken to resolve them, keep reading.
Features & Specifications of Remington Model Four:
| Action | Semi-auto, gas-operated |
| Caliber | .243 Winchester 6mm Remington .270 Winchester .280 Remington .30-06 Springfield .308 Winchester |
| Product weight | 7.5 pounds |
| Product length | 42 inches |
| Capacity | 4 |
| Barrel length | 22 inches |
| Sights Scope | Adjustable Rear Sight/Rail for Scope Mount |
Common Remington Model Four Problems and Solutions
| Problems | Solutions |
| Jamming | Clean the chamber very nicely. |
| Failure To Feed | Tune in the mags, check the bolt. |
| Failure To Eject | Clean the chamber, check the extractor |
| Bolt Doesn’t Lock | Remove bolt head, install new bolts |
| Failure To Re-Cock | Inspect the gas system, clean the shotgun. |
1. Jamming
Jamming is a common problem with the Remington Model 4. Typically, a worn magazine is to blame for a jamming problem. Similar problems affect other versions of the same gun, such as the Remington 742 and 7400. Cartridges stuck in the chamber causing jam as well. The most frequent issue is the fired shell ejects and the following shell goes hallway into the chamber.
The Fix:
In order to effectively clean the chamber, the barrel must be removed. Clean your firearm with a brass bristle jag little smaller than your caliber and a high-speed drill motor. Remove all dust and debris from the chamber. Make sure the magazine is properly positioned and load high-quality ammunition. use lubricant when needed.
2. Failure to Feed
The spent casing would release normally, however feeding the next round is problematic in the Remington model 4. The bullet became jammed in the chamber, and you may have seen the chip on the shell’s muzzle end.
The magazine is not properly installed or the extractor fractured the brass and could not establish a strong grip.
The Fix:
Looks like your mag needs a little fine-tuning. Check to see whether it is only feeding from one side; if so, open the lips on that side to raise the case’s riding position in the magazine.
The problem is that the bolt may be riding over the following round, preventing it from being picked up. A semi-automatic chamber can never be too spotless or smooth, and polishing it can solve any extraction issues. Both things are fairly easy to do.
If you want to take your Rem apart and put it back together, you’ll need a special wrench. It might be easier to just pick up a new magazine and try it out.
3. Failure to Eject
Randomly, the shells will not eject from the Remington model 4. The extractor will rip a piece out of the rim before attempting to chamber a new round with the spent shell still in the chamber. It’s possible to remove the shell with a flathead screwdriver after releasing the clip. It appears to be trying to eject its shell before it is fully expanded.
The Fix:
Make sure the chamber is spotless by giving it a thorough cleaning. Headspace should be addressed if the problem persists. The extractors wore out so quickly. Check if it requires a new extractor.
Extraction might become difficult if the chamber develops pits or becomes unclean. Obtain and employ a chamber brush. I stockpiled a ton of them to give out with gently used
4. Bolt Doesn’t Lock
Some users have complained that when they put pressure on the side bolt release of a Model 4 firearm, the bolt does not move forward. When the clip is inserted, the bolt will not remain in the locked back position. The locking lugs, which connect the bolt to the barrel extension, may be significantly damaged or missing.
The Fix:
My advice is to take a closer look at the shotgun, possibly consulting a gunsmith. There are good reasons why not all lug positions really have lugs.
However, the bolt head can be replaced if necessary; however, headspace concerns dictate that this be done by a gunsmith or, ideally, Remington.
Check the trigger’s entry into the stock; that’s where the bolt will come out. A square/rectangle toggle button needs to be placed just in front of it (inside the trigger guard).
Insert that and, while holding it, draw the bolt backwards (out). With the button depressed, the bolt should come out without much trouble. In most cases, a new bolt may be ordered from your local gun shop.
5. Failure to Re-cock
The Remington 4 will shoot and reload after being manually ejected, but it will not re-cock after being fired. If the firearm will cock when manually cycled but not when shot, the bolt likely isn’t moving far enough backwards during the firing cycle.
The Fix:
My advice is to have the gas system checked out and possibly cleaned. While cleaning the gas system, you should also thoroughly clean the chamber. When a magazine is loaded to its maximum capacity (plus one round), it causes too much drag, causing the bolt to move excessively slowly. Possible defect in the Model 4’s construction. A small amount of slippage from the dust cover on the receiver prevents the weapon from going into full charge.
User Feedback on Remington Model Four
Those who have shot with the semiautomatic Remington Model Four have mixed reviews. While it may be the perfect shotgun for some, it has caused problems for others.
One user commented that the Model 4’s are outstanding rifles and that the 30-06 chambering is great.
Another customer remarked that model 4 rifles are of high quality, and that the 30-06 chambering is exceptional.
As stated previously, the Remington 4 is not without problems. It has problems that the majority of users have encountered.
Another user mentioned that one of his friends had a.270 Winchester Remington model 4. The plunger-style ejector is jammed inside the bolt body, preventing the bolt from being ejected.
Top 3 Alternative Guns of Remington Model Four
Based on comparing the specs, features, practicality, and performance, I have found the 3 best alternatives to Remington Model four.
Remington Model 7400
Most people think the Model Four is an enhanced version of the 7400. A straight comb stock and a checkered pistol grip are the most noticeable variations.
Remington Model 742
Compared to the 742, both the Four and the 7400 are significant upgrades. It also known as the Woodsmaster and it uses a 4-round magazine, a 10-round magazine, and a rare 20-round magazine.
Remington Model 740
Although the 740 and the 742-look identical, they are actually two different models. The features of Remington 740 are similar to of the model four. The 740’s barrel nut is only accessible with a special spanner.
Frequently Asked Questions (FAQs)
What caliber does the Remington Model Four feature?
It features .243 Winchester, 6mm Remington, .270 Winchester, .280 Remington .30-06 Springfield and .308 Winchester.
What is the newest Remington shotgun?
870 ‘FIELDMASTER’.
When did the Remington Model 4 first appear?
Remington Arms produced the Model Four from 1981 until 1987.
What is the price of Remington Model 4?
The current average value of a used Remington Model 4 rifle is $844.18.
Is Remington Model 4 an enhanced version of model 7400?
The Model Four, like the Model 7400, is essentially a redesigned Model 742.
Conclusion
I’ve done my best to describe the Remington Model 4’s difficulties, as well as their possible causes and solutions.
You may discover that the suggested remedies are inadequate for the challenges you’ve encountered. In this situation, you should likely consult a gunsmith or ship the shotgun to Remington for maintenance.
