Remington manufactures a rifle with a bolt action called the Model Seven. The first Model Sevens appeared on the market in 1983. It is offered in a vast array of calibers and finishes.
This Model 7 has some problems that may be annoying. Issues with accuracy, feeding, the trigger, the bolt often crop up, barrel issues and jamming problems are common.
This article explores potential root causes and remedies for various issues. Keep on reading to find out.
Features & Specifications of Remington Model 7:
| Action | Bolt Action Rifle, Repeater Type |
| Caliber | .222 Remington, .223 Remington, .243 Winchester, 6mm Remington, .260 Remington, 7mm-08 Remington, .300 Winchester Short Magnum, .308 Winchester, .350 Remington Magnum |
| Grip | Synthetic |
| Product weight | 6.5 pounds |
Product length | 39.3 inches |
| Capacity | 4-Round Internal magazine |
| Barrel length | 20 inches |
| Barrel Material | Blued carbon steel |
Common Remington Model 7 Problems and Solutions
| Problems | Solutions |
| Accuracy Issues | Clean the shotgun, tighten the screws. |
| Feeding Problems | Install new magazine spring. |
| Trigger Issues | Contact Remington |
| Bolt Issues | Clean bolt stop slot, install new bolt stop spring. |
| Barrel Issue | Replace factory barrels |
| Jamming Problem | Install new magazine spring. |
1. Accuracy Issue
If you possess a Remington Model 7, it may be challenging to achieve consistent accuracy. The only catch is that it’s difficult to construct reliable precision from it. In many cases, it will make contact with both, but the location of the hit will move.
The Fix:
Take it apart, give it a nice cleaning, and get a few extra boxes of ammunition to see if it helps.
Check the tightness of the screws attaching the action to the stock. Because wood naturally swells and shrinks, loose screws form over time. This makes the stock less accurate.
2. Feeding Problems
The Remington 7 bolt does not catch and rounds into the chamber. When more than two bullets are inserted into the blind box magazine, the gun may fail to feed.
The cartridge may not feed because the bolt misses the back of the cartridge and doesn’t pick it up. The problem is that the primer end of the cartridges seems to swivel readily while being inserted into the magazine, making reloading a bit of a chore. A clip or retainer near the magazine’s front appears to hold or secure the cartridge shoulder.
The Fix:
It’s possible that the spring is in the wrong place or that the follower is in the wrong direction.
When reloading, the coal may be too long, and the bullet may seize on the magazine box, keeping the shell’s base down long enough for the bolt to pass over it.
The issue can be remedied by installing a new magazine spring. Be sure the cartridge’s end is flush with the magazine’s back wall.
3. Trigger Issue
The Remington Model 7’s primary defect is its trigger. The shotgun’s trigger could be a major hindrance. To disable the safety mechanism, the trigger is pulled. Changing the trigger’s position and pulling very hard might cause the weapon to discharge if the safety were off.
The Remington manufacturer designed a safe but heavy (9 lb.) trigger for this firearm. This defect appears once the trigger has been upgraded (replaced).
When the gun’s safety is released (when it was empty) and the weapon is fired, it becomes much deadlier. Because of this error, someone’s life may be in jeopardy.
The Fix:
Many Remington owners have reported success after changing the sear screw. If there is any play in the trigger lever and the connector piece, you could end up in a perilous condition that cannot be replicated by slamming the stock’s butt on the floor. Call Remington if you need to be safe.
4. Bolt Issues
A new Remington Model 7 has an unsettling issue: after firing a few rounds, the bolt becomes extremely heavy and difficult to raise, making it impossible to extract the spent cartridge. This occurs with several ammunition kinds.
It’s not a problem of chamber buildup because after one round the bolt opened normally, the next it stuck, and the third it opened normally again.
The bolt becomes frozen in winter as well. Unless it’s a problem with the Bolt’s mechanics. There may be a major issue with the head space.
The Fix:
Install a new bolt stop spring after cleaning the bolt stop slot of metal burrs. Contact Remington about this issue. After repairing it, it will be sent back to you. Having your local gunsmith look at it will help you figure out what’s wrong.
5. Barrel Issue
Remington model 7 factory barrels are a major source of trouble. Many manufactured barrels are rough right out of the box and foul easily. Furthermore, there are problems with accuracy because of the inside barrel dimensions.
The Fix:
You may add replacement barrels, which is a good idea because the factory barrel has a lot of issues.
6. Jamming Problem
The model has issues with jamming, namely when the rear of the cartridge would fall down into the magazine box and the nose of the bullet would jam into the receiver.
This was consistent throughout the entire magazine with all of its sections. Magazine springs may be weakened or worn out and causing this problem.
The Fix:
Install new magazine spring. Your problem can be fixed by giving the shells a very tiny re-bend so that the bottom of the shells remains raised while the action is being cycled. You can also send your rifle back to Remington for fixing your problem.
User Feedback on Remington Model 7
On various online platforms, Remington model 7 users have expressed a wide range of opinions.
According to one reviewer, these are a nice, budget version of a Remmy bolt action. These rifles don’t have a lot of bells and whistles, but they’re incredibly effective in the field.
Another person remarked that the firearms are, without a sure, adorable. When his daughter was 10, he bought her a Remington Model 7 in.260, and she used it for the next four years. She used it to take down a number of deer, as it was easy to use and accurate with handloads.
Nevertheless, there are a number of problems with the Model 7 that have left customers dissatisfied. According to one dissatisfied client, he has been using a Remington model seven stainless synthetic in 7mm 08 but has been having trouble with maintaining accuracy.
Top 3 Alternative Guns of Remington Model 7
Remington Model 700
The triggers for the Model Seven and 700 are different. The bolt-releasing systems is different as well. The Remington 700 include factory triggers; however, the Timney Model 721 is installed in the model 7. Model Seven has a smaller rear action screw than the Remington 700.
Ruger Model 77RSI Mark II International
Adjustable trigger and 2 inches larger barrel are Model Seven’s best features. The M77 International is lighter. Ruger International’s aesthetics, scope mounting technique, and weight assist decrease recoil. It’s easier to fire than the Model Seven, especially at the range.
CZ 527
The CZ has a superior trigger and is probably more accurate right out of the box. The CZ 527 outperforms the Remington Model 7 in terms of accuracy.
Frequently Asked Questions (FAQs)
When was Model 7 Remington made?
1983.
How much does a Remington Model 7 weight?
6 ½ pounds.
How many rounds does a Remington Model 7 Hold?
The Model Seven’s internal magazine holds four rounds.
Are Remington Model 7 still made?
No.
Conclusion
In this article, I have done my best to lay out the issues with the Remington Model 7 and provide possible remedies.
There’s a chance the issues you’ve encountered are too complex for the answers provided. The best course of action would be to take the pistol to a gunsmith or send it in for maintenance to Remington.
