Glock 36 Problems that New Buyers Should Know About

The Glock 36 in its .45 ACP caliber is a marvel! It excels at being undetectable. thin, light, and portable. Significantly different from a G30S

Despite being so concealable and overall an amazing .45 ACP, it has some faults. The most common Glock 36 Problems are: failure to eject, failure to extract, not going to battery, failure to feed and slide lock issues.

I will discuss the solutions to all these problems on Glock 36 and also discuss user reviews in this article. So read on till the end!

Features & Specifications of Glock 36:

Barrel Length96 mm
Magazine CapacityStandard: 6
Overall Length177 mm
Caliber.45 Auto
Twist Rate400 mm / 15.75 inches
Rear SightDovetail Sight
Front SightWhite Dot
SafetySafe Action System
Dimensions Width (Overall): 30 mm Height incl.Mag.:120 mm
WeightUnloaded: 635 g Loaded: 765 g
Trigger Pull28 N
Glock 36 Problems and Solutions
Glock 36

Common Glock 36 Problems and Solutions

Failure To EjectClean and troubleshoot; change ammo.
Failure To ExtractReplace parts.
Not Going to BatteryClean and troubleshoot; change ammo.
Failure To FeedChange ammo.
Slide Lock IssuesTroubleshoot; replace slide lock springs.

1. Failure To Eject

The G36 fails to eject at around the second or third pull of the trigger. You may face these several extraction jams.

Possible Reasons

Your gun may have dirt building up. Using moderately powerful ammo is another cause of gun jamming.

Poor recoil spring assemblies and return to battery issues may additionally aggravate the problem.

The new shell gets jammed over the top of the spent casing. This remains stuck in the chamber.

The Fix

Completely disassemble the frame, then diligently clean every component.

Assuming the malfunctions were caused by shooting range ammo, lubricate it before trying some hotter ammunition. In the barrel, put a dot of red gun grease too.

Test it out with 50 defensive JHP rounds to see if it works. If nothing else works, return it to SIG.

2. Failure To Extract

The Glock 36 has an intermittent extraction problem. These issues seem to get exaggerated with the Gen 3 models more.

Possible Reasons

Extractor grooves can vary causing this problem. I have heard users experience guns that will run fine with everything else but simply won’t run “brand X.”

The extractor is prone to rim slippage. The extractor may not look chipped, and the chamber won’t appear to be worn down.

The Fix

You need to replace a lot of parts. For example:

  • Factory Barrel,
  • Recoil Spring Assembly,
  • Ammo,
  • Extractor Depressor Plunger,
  • Depressor Plunger Spring (to a heavy-duty spring),
  • the LCI Spring-Loaded Bearing (to a non-LCI Spring-Loaded Bearing).

Otherwise, check for the casing being pulled or held by another object. Slowly cycle your hand to see if it is catching.

Frequently, the case mouth of the subsequent round in the magazine will knock the case head off the extractor. Clean the chamber of debris and burrs.

3. Not Going to Battery

When reassembling the Glock 36, the slide goes on and on. When fully retracted, the slide will not stop where it should.

Possible Reasons

It’s possible that the plastic recoil assembly is not straight. When attempting to reassemble the gun, it catches on something inside the frame.

Slide lock spring breaking can cause improper chambering. The guide rod may be the problem too!

The Fix

A new steel guide rod should solve the issue, in my opinion. The 36 uses a different front sight screw.

So if you remove the front sight and it works, you have the wrong sight. Change the sights.

4. Failure To Feed

The gun may be failing to feed every three to five magazines. Usually, it occurs during the second round. Both a white-knuckle grip and a limp-wristed grip causes this to happen.

Possible Reasons

Weak, filthy, and unoiled springs in the gun and magazine cause this issue. However, between late 2005 and early 2006, there was a string of poor 35s.

The more recent weapons work just fine.

The Fix

Clean the filthy gun and lubricate the gun. It might be a good idea to remove the barrel and clean the feed ramp.

Every time, hollow point ammo from Remington, Federal, Hornady, and other brands works best for self-defense.

5. Slide Lock Issues

When there are bullets in the magazine, the slide often locks back. Additionally, it won’t function if there is only one round in the magazine.

This might occur with various stock mags.

Possible Reasons

If the gun is completely stock and has never been disassembled, your thumb is hitting it.

Once you start shooting and fatigue sets in, your grip starts to slide inward and your thumb gets closer to a slide lock.

The locking block pin may not be beneath the slide. Besides, the 36 seems to break the slide lock springs quicker than other Glock models.

The Fix

Verify that the locking block pin is beneath the slide stop spring. Your Glock becomes a single-action pistol if it is not.

Replace the slide long springs.

User Feedback on Glock 36

The G36 is arguably the most contentious Glock model ever produced. It’s a wonderful rifle for some. Others view it as their worst nightmare: a jam-o-matic that would be more useful as a paperweight. Ouch!

However, the reports of any reliability issues with the Glock 36 have been minimal, as far as I can tell.

Most users have not experienced any issues with the ball, HP, or LSWC ammunition. They now have the confidence to carry it as CCW with them because of this.

The one flaw that bothers them the most involves magazines. Only the G42 and G43 can use the larger magazines from a larger Glock. Such as the G26, which can use the magazines for the G34, G17, and G19.

The G36 that are now being produced are also good. The previous ones lacked dependability. You will receive two more rounds if you take into account the J frame S&W. Recoil can also be strong, but with practice, it becomes highly controlled.

Yes, I know the problems that I’ve discussed in this article seem scary. But the bright side is brighter, to be honest! Overall, users tend to be highly satisfied with their Glock 36.

Top 3 Alternative Guns of Glock 36

Based on comparing the specs, features, practicality, and performance, I have found the 3 best alternatives to Glock 36. 

S&W Model 457

This is the least appreciated 45 ACP compact ever produced. Bit of an underdog and you’ll agree with me once you get your hands on it! It can consume any ammunition that is supplied to it and is combat accurate.

S&W Model CS45 “Chief’s Special”

It is the same gun as S&W Model 457 but with different capacities. They are similar in size to the G36.

Para C6.45

It means “Para Carry, Light Double Action Trigger, 6 Rounds.” In the same holster, they are marginally more comfortable and concealable than the G36.

Frequently Asked Questions (FAQs)

What is a good CCW mag carrier for the Glock 36?

Neo Mag is a good one. You can buy them here.

Between Glock 36 and 27, which is more accurate and concealable?

According to hundreds of users, Glock 27 is more accurate and concealable.

How to reduce thumb pain from the Glock 36 frame?

Fasten a maxi pad to the grip with duct tape to alleviate the pain

What Glock is the same size as the Glock 36?

Glock 23.

Is Glock 30 better than 36?

Yes, in terms of less recoil and smoothness of shooting, definitely.


Most folks have owned Glock 36s that have always performed flawlessly. It shoots really well and makes a fantastic carry handgun.

The Glock 36 problems won’t let you down if you do your job. But for some individuals, the 7 rounds followed by 6 on a reload may be a turn off.

I think it’s crucial to have faith in your ability to hit the target. Its always wise to use your judgment to avoid wasting ammunition.

To sum up, G36 is capable of being the most fluidly shooting Glock you’ve ever used. I would strongly advise you to take the bet!

Leave a Reply

Your email address will not be published. Required fields are marked *

Related Posts