4 Ruger LCR 357 Problems that you are not aware of

Ruger has done a wonderful job through bringing the LCR 357 to the customers with its excellent features. However, there are a few Ruger LCR 357 difficulties to be aware of before making hurried decisions.

The most typical Ruger LCR 357 complaints are about cylinder issues, ammo issues, reliability issues, and so on.

This article will discuss the possible causes and remedies to these issues. So, let’s get this party started.

Features & Specifications of Ruger LCR 357:

Magazine Capacity5
Overall Length6.50”
Caliber.357 Magnum
Barrel Length1.875”
FinishBlackened Stainless
Weight17.10 oz.
Common Ruger LCR 357 Problems and Solutions
Ruger LCR 357 Problems

Common Ruger LCR 357 Problems and Solutions

ProblemsSolutions
Cylinder IssueTry alternative ammo to see if the problem persists. Contact Ruger if these checks come up negative.
Ammo IssueCleaning or brushing the cylinder is important. Also, verify the ammunition.
Reliability IssueFixing the cylinder is necessary. Examine the primer. If the primer seems to be cracked or damp, it must be replaced.
Failure to EjectClean the gun to resolve this issue.

1. Cylinder Issue

Some of the LCR 357 users have complained about the cylinder issue.

Users immediately spotted a severe problem after firing a few bullets. The cylinder would occasionally stop spinning.

Possible Reasons

If the gun does not allow the finger to reset the trigger, the cylinder can be locked.

The casing head gap may be too thick, or the primers may be backing out. Both of these conditions can cause the cylinder to lock.

Examine the ammunition you’re using which may create flaws.

The Fix

Before attempting more complicated processes, try simpler solutions such as changing the ammo, which may be of poor quality.

Try different ammo to see if you have the same problem. If these checks come back negative, contact Ruger.

You can capture the cylinder by pushing it into the frame. If you have to do this every time, it sounds like the frame is misplaced. You should contact Ruger and explain the situation to see what they say.

Examine the pawl to ensure that it works properly. Keep the cylinder open while cycling the action and keeping an eye on the pawl. Also, make sure the extractor isn’t sitting on grit or lint and that it’s working properly.

Verify that the bullets are not going forward from the casing.

2. Ammo Issue

Your favorite LCR 357 may experience problems on occasion because of ammunition.

The cases are split halfway down the length of the case, right above the rim.

Possible Reasons

Fired cases may stick due to the crud ring from the shorter cased ammo.

Users cannot forget that the cylinder can be a reason why ammo can cause issues with your gun.

According to one user, the crud ring prevented new ammo from sliding completely into the cylinders, making it difficult to index to the next round.

The Fix

The cylinder bores are extremely tight. Keep a bore brush on hand to clean the cylinder when it becomes clogged. After cleaning or brushing the cylinder, the gun will shoot quite well.

Moreover, extraction may appear to be quite difficult, so verify the ammunition.

Some firearms just do not like particular loads.

Look for signs of pressure on primers and cases.

3. Reliability Issue

After buying a Ruger LCR 357, consumers may think everything is okay with the gun. However, after a short period of usage, the problems start occurring with reliability.

Possible Reasons

The cylinder is a concern in such cases that would not lock when closed and would freely spin past each chamber.

The gun occasionally fails to discharge. This can occur due to a variety of factors, including a faulty primer, incorrect ammo, or a dirty pistol.

If the sights are not correctly adjusted, the accuracy of the LCR 357 may also bother you.

The Fix

First of all, if you’re experiencing trouble with reliability, fix the cylinder issues the right way. I have already mentioned how to get rid of cylinder issues.

The first thing you should do if your gun fails to fire is to inspect the primer. If the primer appears to be broken or moist, changing the primer is mandatory.

You should also inspect the ammunition to ensure it is not faulty. Finally, if everything else fails, you might need to clean your gun. Failures to fire are frequently caused by a dirty gun.

You can boost the performance of your 357 by executing a few things. To begin, ensure that the sights are correctly aligned. They will need to be modified if they are not.

You can also experiment with different types of ammunition to discover whether one type works better in your gun than another.

Do not forget that the more you practice shooting your gun, the better you’ll get at hitting your target.

4. Failure to Eject

Another frequent Ruger LCR 357 issue is failure to eject.

After shooting up to ten shots in a row, the plunger will not eject the brass unless it is heeled forcefully with the palm on the second panic reload.

Possible Reasons

This can happen if something is in the way of the ejected shell casing. Typically, this obstacle is a bit of dirt or debris.

Moreover, the ejector rod is not long enough to entirely expel the cartridges without a violent slap. Such a state can cause issues.

There’s a chance that oil got into the cylinders.

The Fix

You will need to clean the gun to resolve this issue. You can accomplish this by disassembling the gun and cleaning all of its components.

After cleaning the gun, reassemble it and test it to determine if the problem has been resolved.

User Feedback on Ruger LCR 357

The Ruger LCR 357 user reviews tend to be uneven, with the majority of them being unfavorable.

According to my study, the issues with LCR 357 mostly occur because of the faulty cylinder.

A user stated that the problem is trying to swing out the cylinder to eject the expended cartridges. The release button pushes in, but he has to push pretty hard on the cylinder to remove it from the frame. He put 200 rounds through it with four different types of ammunition, both 357 and 38. However, it was hard to deal with the gun every time he used it.

Another reviewer claims the gun works flawlessly and is pretty accurate.

However, the cylinder release is occasionally difficult to push and has a little rough or gritty feel to it. The button is quite small and difficult to press.

It has improved after being blown out with compressed air (80psi) and thoroughly lubricated. When the cylinder is open, the button is free to move.

Top 3 Alternative Guns of Ruger LCR 357

I discovered the three best Ruger LCR 357 alternatives by considering specifications, features, functionality, and performance.

Smith & Wesson 642

The Smith & Wesson 642 is possibly the best in the business. The Centennial J-frame is easy to conceal and will not hang up or snag in a pocket or holster. Despite its little 1.875″ barrel, it shoots remarkably straight.

Taurus 605

The Taurus 605 is an excellent example of a high-quality pocket pistol. It’s compact and easy to conceal, yet it packs a powerful punch. With an overall length of only 6.5″, it is substantially smaller than the majority of handguns and shoots with precision and dependability.

Ruger SP101

Despite its somewhat higher price, the Ruger SP101 is a very robust revolver that is a good alternative for anyone who needs a solid revolver for self-protection.

Frequently Asked Questions (FAQs)

How much does Ruger LCR 357 30 cost?

A Ruger LCR 357 gun can cost $829.00 currently. 

What is the weight of a Ruger LCR 357?

A Ruger LCR 357 unloaded weighs 17.1 ounces. That’s quite light for a Magnum. 

Is it possible to shoot 38 Special with a Ruger LCR 357?

The LCR-357 can now assimilate ammo in the.38 and.357 Magnum calibers. Ruger, unlike several other manufacturers of ultra-lightweight revolvers, does not advise against using lightweight ammunition.

When did the Ruger LCR 357 come out?

Ruger launched the LCR-357 chambered for. 357 Magnums in June 2010.

Conclusion

I’ve talked over Ruger LCR 357 issues, causes, and solutions as thoroughly as I could.

However, the answers provided may not be adequate for your needs.

Talking with a gunsmith or mailing the revolver to Ruger is the best solution in such cases.

Leave a Reply

Your email address will not be published. Required fields are marked *

Related Posts