Remington 710 Problems that New Buyers Should Know About

The Remington 710 is an excellent and highly accurate rifle. It also makes shooting paper targets a breeze! It is enough for a hunter who is less picky and wants a less expensive gun.

However, the finicky part of the gun follows the user along. The most common problems with the Remington 710 are: bolt stop failures, poor quality and design of barrel, action problems, trigger problems and cheap make.

I will give you the solution to these common issues in this article. Additionally, you will get authentic reviews from users as well. So, stay tuned!

Features & Specifications of Remington 710:

Action: Bolt Action

Caliber: .270 Win, .30-06 Sprg, 7mm Rem Magnum etc.

Product weight: 7.125 lbs.

Product length: 42.5 inches

Capacity: 3/4 round detachable magazine.

Stock: Synthetic

Barrel length: 22 inches                 

Remington 710 Problems
Remington 710

Common Remington 710 Problems and Solutions

ProblemsSolutions
Bolt Stop FailuresMake sure to lock the bolt.
Poor Quality and Design of BarrelSend to Remington.
Action ProblemsReplace the gun.
Trigger ProblemReplace the trigger.
Cheap MakeN/A

Bolt Stop Failures

The bolt breaking off is a notoriously common problem with the Remington 710s. The bolt shroud also breaks pretty easily. Additionally, the bolt’s front portion could be out of alignment with the rest.

The Fix

image 6

The lever for the 710 bolt release pivots back to unlock and forward to lock. It could get snagged on something and snap off if you forget

to lock it back down. Users make this mistake a lot after a cleaning session.

Avoid cycling the bolt too quickly and avoid sleeve tangle-ups when closing the bolt. Doing this can damage the shroud.

Poor Quality and Design of Barrel

The barrel of the Remington 710 is hydraulically pressed into the receiver and joined to it permanently. The fit, however, is terrible.

The barrel is only partially seated in the receiver and is removable. One screw on the magazine’s front holds it in place and another screw secures it to the stock.

The Fix

The barrels’ poor fit is a manufacturing fault. An inexpensive product that is produced in large quantities may occasionally contain a lemon. This is the case with the Remington 710s.

Send the gun to Remington. They’ll either give you a new gun or a refund.

Action Problems

The action freezing is another problem. This issue gets worse when using 400–500 rounds of inexpensive ammunition, such as, Federal American Eagle 155gr FMJ.

Every couple of boxes, on average, the action would freeze and the bolt would be extremely difficult to open.

The Fix

The action’s soft rails quickly gouge, making it incredibly stiff and rough. I believe that changing the rifle is the only viable solution to the issue. The 710 is unquestionably a throwaway after entry-level.

Trigger Problem

The Remington trigger problem dates back to the 1970s. Remington has also issued recalls because of this. The factory trigger is overly heavy, which causes the gun to jerk.

It appears like the gun trembles before the sear releases. But 710 trigger is an electrical switch, there are no sears.

The Fix

The triggers had many problems when they were replacing the Walker triggers on 710s. This is quite ironic.

The 710’s single-stage trigger is made of cheap metal and isn’t quite as good as the one that came with the 788. The warranty will be invalidated if you meddle with the trigger!

The weight of the trigger cannot be reduced. You can replace the trigger, however. It will be expensive though.

Do not get the “upgrade” from Remington, even if it’s offered. Simply purchase a Timney or other posh trigger.

Cheap Make

Guns jamming, finicky coating and groups fired consistently being under 2 MOA are some common complaints. Over time, the 710 has developed a reputation for being unreliable and finicky.

The Fix

This entry-level gun was made by cutting corners. It has lousy machining and finishing and is built extremely cheaply. Even the metal is just coated garbage.

They have a lot of plastic on them to make them cheaper. The bolt is very tacky. The stock also resembles a vintage synthetic .22LR. And they typically only last for 500 rounds until something breaks or it stops working.

There is no fix to this. You just have to treat it as an entry-level gun and then forget about it.

User Feedback on Remington 710

There are so many conflicting opinions on the Rem 710. Some claim it is pure, unadulterated garbage. Its design is deemed poor because of the press-fit barrels and plastic guide rails.

On the other hand, some say, even the most affordable Stevens/Savage would be an improvement. Some claim that the Rem 710, like the simple girl at the dance, is underappreciated while having a lot of promise.

In a 270, it is quite precise and reliable. Some people like the model 710 over the Model 770 that came after it. It looks better than the Savage Axis. It is not a wonderful gun, but neither is it a bad one.

There really isn’t much that can be done to customize it, other than painting the stock and mounting a better scope. Because the barrel and receiver/bolt carrier is combined.

There is a “hick-up” in the transition from the plastic receiver to the metal barrel (due to the interior barrel’s receiver’s plastic construction).

But I believe, the gun is not overestimated. As an entry-level gun, it is good.

Top 3 Alternative Guns of Remington 710

Based on comparing the specs, features, practicality, and performance, I have found the 3 best alternatives to Remington 710 .380 semi-automatic revolver. 

Savage 110

When it comes to value and toughness, Savage is tough to beat. From a user perspective, the Savage 110 is better. The Remington 710 has a weak, cheap feel to it.

The Savage bolt-on is initially stiff and gritty but does get a little more supple with use.

Remington 770

The 710 has already garnered so much criticism for Remington that they no longer produce it. Instead, they came up with the 770. They have the same appearance.

Yet, purchasing a 770 will give far better outcomes. The 710’s trigger is superior to the 770’s though.

However, a 770 has a far better overall build. But, both have poor action.

Howa 1500

The Howa 1500 is a fantastic shooter in both 308 Win. and 300 Win. Mag. Although a big beast, it is reliable and precise.

Unlike the rough bolt on the Rem’s 710/770, this one is smooth. It is also reasonably priced.

Frequently Asked Questions (FAQs)

What is the dimension of the stock Remington 710 scope?

The stock scope dimension is 3 x 9 x 40.

What is the accuracy of Remington 710?

It can shoot 100-yard groups under 1″.

What type of rifle is Remington 710?

An entry-level hunting rifles.

What can be a better Remington 710 scope alternative?

Marlin makes a fine bolt action for about the same money.

What is the Inside of the Remington 710 Receiver Built With?

Plastic, all the way to the barrel.

How is the Barrel Built on a Remington 710?

The barrel is hydraulically pressed into the receiver and permanently attached to it.

Conclusion

The Remington 710 lacks the qualities of an M700 so to say. But is still worth the low price paid.

It is an incredibly accurate weapon. Especially while shooting tight, 200-yard groups. On a bad day, most of the inexpensive guns available today will shoot MOA lesser than Rem 710.

Overall, I would suggest you purchase another gun if you don’t want problems.

Leave a Reply

Your email address will not be published. Required fields are marked *

Related Posts