As a result of his extensive experience with firearms, John Pedersen gained a lot of respect. The Remington Model 14 pump-action repeating rifle was his brainchild, and it spawned two iterations, the Model 14 1/2 and the Model 141.
A number of new and interesting ideas went into the making of the Model 14.
However, there are issues with this gun that need fixing. problems with firing, jamming, reloading, firing pin not releasing, and misfires are common issues that arise when using this model 14.
If you want to know more about the issues with Model 14 and the subsequent remedy, keep reading.
Features & Specifications of Remington Model 14:
| Action | Pump-action |
| Caliber | .25 Remington .30 Remington .32 Remington .35 Remington |
| Product weight | 7.75 pounds |
| Product length | 42.75inches |
| Capacity | 5 rounds + 1 |
| Barrel length | 24 inches |
Common Remington Model 14 Problems and Solutions
| Problems | Solutions |
| Failure To Fire | Install new “dog” spring. |
| Jamming | Replace the spring and brush guard |
| Loading Issues | Use correct length brass |
| Misfires | Install new firing pin |
| Heavy Slid Action | Adjust magazine spring pressure |
1. Failure to Feed
There are issues with feeding on the Model 14. The shell is not raised sufficiently for feeding into the chamber. If you are using factory ammunition, we can rule out the ammunition as the source of poor feed, leaving only the carrier dog spring.
Reloaded ammo accounts for roughly 80% of all feed/eject issues, while a weak/broken carrier dog spring accounts for 10%, and the other 10% can be attributed to a wide range of carrier/stop/follower issues.
The Fix:
You may test your “dog” by flipping it back and forth against your fingernail; it should flip in either direction with vigor and “smart” somewhat when it strikes your fingernail. The carrier should glide effortlessly in the channel; any binding indicates a problem with the carrier friction plunger, which may be preventing the feed mechanism from functioning as intended.
Install new dog spring. Installing them is easy after 20 or 30 times. Any spring may fit; some may need to be cut and tested. During installation, they are also simple to deform.
2. Jamming
Model 14 is susceptible to jamming issues. while reversing the foregrip causes it to jam. The spent shell is dangling from the collet. Even if you manage to extract the bullet, the next one could get stuck at the bottom of the chamber, rendering the gun unusable.
The Fix:
The brush guard is located at the end of the magazine and is fastened in place by a single slot-head screw. Turn the gun so that the magazine ring slides out and the shells come out with it. Removing the spring relieves the pressure, and then replacing the spring and brush guard will fix the problem.
3. Loading Issues
When reloading a Remington Model 14, problems can arise if the last bullet fired had a backed-out primer. This may be the result of a loose priming pocket or oversized brass. Rarely, a primer might appear to have backed out of the brass. Reason for this is a lack of pressure or the powder you need is in the bottom compartment.
The Fix:
Make sure all of your brass is the correct length and try sizing until you can barely get the slide to chamber and shut the round, then back it down a little more for fail safe chambering. You can increase the amount of powder you’re using.
4. Misfires
There are problems with the Remington model 14 that cause it to misfire. One out of every four attempts fail. Possibly the firing pin or breech block interior is clogged, or the firing pin is damaged.
The firing pin is not consistently hitting the chamber; this could be due to a loose spring or a too-short pin are causing misfire.
The Fix:
Check the firing pin and replace it if it’s damaged. If dirt has clogged the firing pin or breech block, clean it out.
The gunsmith will be able to tell you if the firing pin is too short or the spring is worn out, allowing you to make the necessary adjustments.
5. Slide Action Issue
The slide action has a quirk. Always rack the slide firmly while chambering a round, especially when the magazine is full to prevent the cartridge’s nose from jamming against the breech, which is located below the opening of the chamber. The jam wasn’t difficult to dislodge.
In other cases, this may occur only if there are more than three bullets in the magazine. The slide action felt somewhat heavier than that of a pump shotgun. The weight of the magazine, the action bar, and the cartridges that is in the magazine need shifting in order to move the slide.
The Fix:
The main cause of the problem is magazine spring pressure. Adjust the spring pressure. To decrease the heavy feel of the slide and avoid jamming, load three rounds in the magazine and chamber one, this will give m two backup rounds.
User Feedback on Remington Model 14
Although it’s an older model, the Remington Model 14 still has its own dedicated following. However, while looking at other forums and discussion groups, different perspectives on this paradigm become apparent. Few people like it, and few people have had problems with it.
One user considers the ancient Remington pumps, 14 and 141, to be magnificent rifles and excellent specimens of old-school gun making. His family reveres the Rem 14 or 141 in.35 caliber as the grail of deer rifles.
Another user commented, the 14 and its later 141 with a pistol grip stock are superbly built guns from a past we rarely see now. The magazine tube’s spiral design keeps spitzer bullets from touching the primer in the cartridge in front of them, making this a revolutionary design that allows for manual loading.
However, there is people who faced issues with their model 14. Another user who possesses a 1919-vintage Model 14 in 25 Remington has noted that, on rare occasions, the firearm will fire even when the action has been closed.
Top 3 Alternative Guns of Remington Model 14
Remington 7600 Rifle
Remington 7600 rifle combine pump action with a sturdy locking bolt and powerful cartridges like.308 Winchester and.30-06 Springfield. The Remington 7600 is an excellent bolt-action rifle.
Remington 760
The evolution from the Model 14 to the Model 141 resulted in the creation of the Model 760, a newer, more advanced design with a front locking bolt. It is capable of firing high-powered rounds from a removable box magazine (.270,.280,.30-06, etc.). With this, the period of the Model 14 and 141 rifles with tubular magazines came to an end.
Remington 141
The hardware on the Model 14 and 141 guns is blued steel, the sights are open, and the stocks and grips are made of walnut. Both the rifle and the carbine featured five-round magazines, but the 14’s smaller forearm and shorter barrel (at 22 inches) set it apart from the 141’s longer 24-inch barrel.
Frequently Asked Questions (FAQs)
Who invented the Model 14 rifle?
John Pedersen.
What was Remington’s first pump shotgun?
The Remington Model 31.
Are pump-action rifles any good?
Remington, pump action rifles are very accurate.
When was Remington model 14 was introduced.
1913.
Conclusion
I’ve done my best to be as clear and precise as possible in describing the issues that people typically have with the Remington Model 14 and how to fix them.
Nevertheless, it’s possible that your problems are more involved than the solutions I’ve offered. In this circumstance, your best options are to consult a gunsmith or ship the revolver to Remington for servicing.
