{"id":534,"date":"2022-08-18T18:00:32","date_gmt":"2022-08-18T18:00:32","guid":{"rendered":"https:\/\/gunanalyst.com\/?p=534"},"modified":"2022-09-02T17:17:38","modified_gmt":"2022-09-02T17:17:38","slug":"kel-tec-p32-problems","status":"publish","type":"post","link":"https:\/\/gunanalyst.com\/kel-tec-p32-problems\/","title":{"rendered":"5 Kel-Tec P32 Problems You Should Know"},"content":{"rendered":"\n

Seeing the price, buying a P32 is almost irresistible. But impulse-buying may not be a happy experience after facing issues. After some research, I found 5 Kel-Tec P32 problems that you should know.<\/p>\n\n\n\n

According to user feedback, jamming, faulty firing pin, locked slide, improper cycling, and loosely attached magazine are the common issues.<\/strong><\/p>\n\n\n\n

Here, the good thing is that I have also discussed the possible fixes for your convenience. So, read till the end without skipping any part.<\/p>\n\n\n\n

Features & Specifications of Kel-Tec P32<\/strong><\/p>\n\n\n\n

Kel-Tec P32<\/strong><\/td><\/tr>
Barrel Length<\/strong><\/td>2.7\u201d<\/td><\/tr>
Magazine Capacity<\/strong><\/td>7<\/td><\/tr>
Overall Length<\/strong><\/td>5.1\u201d<\/td><\/tr>
Rear Sight<\/strong><\/td>P-Sight<\/td><\/tr>
Front Sight<\/strong><\/td>Blade<\/td><\/tr>
Safety<\/strong><\/td>Long double-action trigger pull; Internal hammer block<\/td><\/tr>
Dimensions  <\/strong><\/td>3.5\u201d H; 0.75\u201d W<\/td><\/tr>
Weight<\/strong><\/td>7 ounces (unloaded)<\/td><\/tr>
Trigger Pull<\/strong><\/td>5 pounds<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n
\n
\"Common
kel-tec p32<\/figcaption><\/figure><\/div>\n\n\n

Common Kel-Tec P32 Problems and Solutions<\/h2>\n\n\n\n

Kel Tec P32 is not free from problems, and you have got an idea about it. Now, let\u2019s discuss them with solutions in detail here.<\/p>\n\n\n\n

Quick Overview of the Problems and Solutions<\/strong><\/p>\n\n\n\n

Problems<\/strong><\/td>Solutions<\/strong><\/td><\/tr>
Not feeding the ammo due to jamming<\/td>Try different brands of ammunition, clean the gun regularly, apply lubricant, or replace the faulty magazine.<\/td><\/tr>
Stuck firing pin preventing rounds from getting in the chamber<\/td>Take the metal piece out that is causing obstruction, trim the peening, and clean the gun.<\/td><\/tr>
Not being able to unlock the slide<\/td>Replace the faulty spring and magazine catch in the system.<\/td><\/tr>
Not being able to cycle properly<\/td>Keep your wrist firm while shooting, clean the gun regularly, and use the right kind of ammo.<\/td><\/tr>
Getting loose magazine sometimes<\/td>Replace the magazine catch and spring if necessary.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

1. Feeding Problem<\/h3>\n\n\n\n

Some new Kel Tec P32 users complain that the ammo gets stuck sometimes.<\/p>\n\n\n\n

When it happens, the bullet gets stuck between the magazine lip and the feed ramp.<\/p>\n\n\n\n

It jams the magazine from getting out.<\/p>\n\n\n\n

The user mentioned that he had to push down the round for getting the magazine and round in the chamber out.<\/p>\n\n\n\n

There are several possible reasons for this kind of problem.<\/p>\n\n\n\n

Not cleaning regularly, using the wrong kind of ammunition, and faulty magazine are the leading causes of the P32 feeding issue.<\/p>\n\n\n\n

The Fix<\/h4>\n\n\n\n

From the reasons, you have probably guessed the solution already.<\/p>\n\n\n\n

But you don\u2019t know which solution you should try first.<\/p>\n\n\n\n

According to the users who have solved the issue, the feeding problem indicates rim-lock. And, it gets solved by trying<\/strong><\/a> a different brand of ammunition.<\/p>\n\n\n\n

Furthermore, you must keep the gun clean regularly. Also, don\u2019t forget to apply the right kind of lubrication.<\/p>\n\n\n\n

Lastly, if the problem still persists, you can try replacing the magazine.<\/p>\n\n\n\n

2. Firing Pin Stuck Forward<\/h3>\n\n\n\n

I have seen several complaints of a round not getting in the chamber regarding P32.<\/p>\n\n\n\n

One user faced this issue; did a little inspection, and noticed that the firing pin was stuck in a forward position.<\/p>\n\n\n\n

Usually, it is a reliable gun but this kind of problem can occur sometimes.<\/p>\n\n\n\n

A probable reason for this peening and firing pin getting stuck problems can be worn springs.<\/p>\n\n\n\n

Also, it is possible that the hammer has peened the firing pin\u2019s back so severely that it hangs up inside the channel.<\/p>\n\n\n\n

The Fix<\/h4>\n\n\n\n

First of all, you have to keep the gun regularly cleaned and maintained. Check the health of the springs regularly, and take action accordingly.<\/p>\n\n\n\n

Also, there are some immediate solutions to make the firing pin work properly.<\/p>\n\n\n\n

You can take off the metal piece that is causing this issue of not chambering the round.<\/p>\n\n\n\n

Also, the gun can be operational immediately using a Dremel bit to clean the peening.<\/p>\n\n\n\n

3. Can\u2019t Unlock the Slide<\/h3>\n\n\n\n

Here, the problem is that the slide would open locked, and it becomes almost impossible to unlock.<\/p>\n\n\n\n

One possible reason for the problem is that the spring becomes so weak that it can\u2019t push down the lock at the right time.<\/p>\n\n\n\n

Another probable cause is oil and gunk getting inside the slide making it sticky.<\/p>\n\n\n\n

The Fix<\/h4>\n\n\n\n

The replacement spring doesn\u2019t cost a lot. Visit the official website of Kel Tec<\/strong><\/a>, and order one.<\/p>\n\n\n\n

And, remember to keep the gun clean all the time. Assembling and disassembling the gun for replacing the spring can take 5 to 10 minutes.<\/p>\n\n\n\n

There are tons of YouTube videos<\/strong><\/a> showing how to do it.<\/p>\n\n\n\n

Even after doing all those things, you may experience small issues regarding the magazine catch. The plastic part wears down easily.<\/p>\n\n\n\n

To solve this, you can either buy several replacement parts or you can search for a metal magazine catch.<\/p>\n\n\n\n

4. Not Cycling Properly<\/h3>\n\n\n\n

Proper cycling ends with extracting the empty shell after shooting. But some new users of the P32 firearm face the problem of not cycling properly.<\/p>\n\n\n\n

According to a forum thread<\/strong><\/a>, the user was facing this problem in 2 out of every 3 shots. The casings failed to extract the shell.<\/p>\n\n\n\n

It happens due to two reasons. Either the user can\u2019t lock the wrist while shooting or the gun is not being cleaned properly.<\/p>\n\n\n\n

The Fix<\/h4>\n\n\n\n

I am assuming that you take care of your small caliber P32 and clean it regularly.<\/p>\n\n\n\n

As a beginner, it is highly likely that you have a limp wrist during the shots.<\/p>\n\n\n\n

While firing small firearms, if you don\u2019t keep your wrist firm throughout the shot, the handgun fails to eject the spent shell.<\/p>\n\n\n\n

Another possibility is that you are not using the right kind of ammunition for the gun.<\/p>\n\n\n\n

5. Loose Magazine<\/h3>\n\n\n\n

Have you noticed that your P32 magazine is getting loose sometimes? Not all but lots of these small handgun users mention the same problem.<\/p>\n\n\n\n

As Kel-Tec uses plastic magazine catch it is likely that the part becomes faulty over time.<\/p>\n\n\n\n

Also, the spring may not have the necessary tension to keep it in place.<\/p>\n\n\n\n

The Fix<\/h4>\n\n\n\n

Try to find a metal magazine catch in the aftermarket parts selling platforms.<\/p>\n\n\n\n

If you can\u2019t find one, replacing it with a new plastic magazine catch will do the work for a while.<\/p>\n\n\n\n

At the same time, inspect the spring of the magazine, and replace it if necessary.<\/p>\n\n\n\n

\n