{"id":4511,"date":"2023-06-21T06:18:14","date_gmt":"2023-06-21T06:18:14","guid":{"rendered":"https:\/\/gunanalyst.com\/?p=4511"},"modified":"2023-09-03T19:28:55","modified_gmt":"2023-09-03T19:28:55","slug":"panzer-arms-bp-12-problems","status":"publish","type":"post","link":"https:\/\/gunanalyst.com\/panzer-arms-bp-12-problems\/","title":{"rendered":"5 Common Panzer Arms BP-12 Problems for Shotgun Enthusiasts"},"content":{"rendered":"\n
The Panzer Arms BP-12 is a shotgun produced in Turkey. Although it has many innovative features, users may face some common problems with the BP-12 shotgun.<\/p>\n\n\n\n
The most common Panzer Arms BP-12 problems are feeding problem, loose hand guard, rough firing pin chamber, cycle failure, and cracking.<\/strong><\/p>\n\n\n\n Continue reading the article to learn more about these troubles along with the proper solutions.<\/p>\n\n\n\n Features & Specifications of Panzer Arms BP-12 Gun:<\/strong><\/p>\n\n\n\n The rounds could occasionally not eject from the Panzer Arms BP-12. As a result, the subsequent bullet misses the firing chamber. The double feed also raises this problem.<\/p>\n\n\n\n This issue occurs more frequently if small shells are used. The gun’s back does not keep the bolt in place. As a result, the rounds are not ejected.<\/p>\n\n\n\n You should feed a couple of chambers with hot loads after unbundling your new Panzer Arms BP-12.<\/p>\n\n\n\n Additionally, you should lock the spring at the back and keep it locked for a while. The spring will become more flexible and loosen up by using different rounds with various discharge velocities.<\/p>\n\n\n\n The Panzer Arms BP-12’s hand guard has a tendency to fall out of place. It will therefore make a collision with the muzzle brake.<\/p>\n\n\n\n If you cycle the gun once again after manually replacing it, you could see that the muzzle brake is pressed up against the hand guard.<\/p>\n\n\n\n To fix this issue, you have to disassemble the Panzer Arms BP-12. Follow the manual to carefully disassemble the shotgun.<\/p>\n\n\n\n Now, inspect the hand guard attachment points. If there are any signs of damage or loose movement, this might be the problem. Tighten the mechanism.<\/p>\n\n\n\n After that, check if the hand guard and muzzle brake are aligned correctly. If they are, you should fix it. If you are unable to do this by yourself, you should send the shotgun back to the dealer or the company or servicing.<\/p>\n\n\n\n The Panzer Arms BP-12 may have a rough chamber. As a result, when the round comes up after shooting to get into the chamber, it gets stuck.<\/p>\n\n\n\n This happens when the firing pin comes out. The sharp chamber is present with some of the BP-12 that might cause this issue.<\/p>\n\n\n\n Get a Dremel and take the ball apart first. Now, take the Dremel<\/a> and apply it to the hole for a while. Sand the area with 800, 1000, and 2000 grit one by one.<\/p>\n\n\n\n Now, polish the hole to make it smooth. This will make sure that the round does not get stuck inside the chamber.<\/p>\n\n\nCaliber<\/strong><\/td> 12 Gauge<\/td><\/tr> Capacity<\/strong><\/td> 5+1<\/td><\/tr> Barrel Length<\/strong><\/td> 20 Inches<\/td><\/tr> Weight (Unloaded)<\/strong><\/td> 3.53 Kilograms or 7.8 lbs.<\/td><\/tr> Weight (Loaded)<\/strong><\/td> 3.90 Kilograms or 8.6 lbs.<\/td><\/tr> Length<\/strong><\/td> 30.70 Inches<\/td><\/tr> Chamber<\/strong><\/td> 3.0 Inches<\/td><\/tr> Action Type<\/strong><\/td> Magazine Fed Semi-Auto Action<\/td><\/tr> Safety<\/strong><\/td> Manual Safety, Ambidextrous HK Type<\/td><\/tr> Sights<\/strong><\/td> Picatinny Top Rail, AR-type Aperture Bead Sights<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n Common Panzer Arms BP-12 Problems and Solutions<\/h2>\n\n\n\n
Problems with Panzer Arms BP-12<\/strong><\/td> Solutions<\/strong><\/td><\/tr> Feeding Problem<\/strong><\/td> Feed with hot loads and lock the spring at the back.<\/td><\/tr> Loose Hand Guard<\/strong><\/td> Disassemble and tighten the hand guard attachment points.<\/td><\/tr> Rough Firing Pin Chamber<\/strong><\/td> Polish the firing pin chamber with a Dremel tool.<\/td><\/tr> Cycle Failure<\/strong><\/td> Calibrate the gas system, and inspect the gas port and block.<\/td><\/tr> Cracking<\/strong><\/td> Avoid using hot magnum loads and replace the broken parts.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n 1. Feeding Problem:<\/h3>\n\n\n\n
The Fix:<\/h4>\n\n\n\n
2. Loose Hand Guard:<\/h3>\n\n\n\n
The Fix:<\/h4>\n\n\n\n
3. Rough Firing Pin Chamber:<\/h3>\n\n\n\n
The Fix:<\/h4>\n\n\n\n