This article contains the answers to these issues. Additionally, the current user experiences with this revolver have been shared. In addition, the best alternatives to this revolver are covered in the article. Read the complete article to learn about the Smith & Wesson 617 problems<\/strong> and their solutions.<\/p>\n\n\n\n Features & Specifications of <\/strong>S<\/strong>mith and <\/strong>W<\/strong>esson 617:<\/strong><\/p>\n\n\n\n The Smith & Wesson 617 revolver has an issue with failure to fire about three or four times per cylinder on average (out of ten rounds). It is a widespread issue with this revolver.<\/p>\n\n\n\n Possible causes include the use of ammunition that is incompatible with the revolver. The other possibility may be that the revolver’s firing pin is malfunctioning.<\/p>\n\n\n\n To fix the problem, change the ammunition you are using. In particular, people have complained about this problem while using the Remington Golden Bullet.<\/p>\n\n\n\n Federal and Winchester are the best ammunition options for preventing failure to fire.<\/p>\n\n\n\n If the problem persists after changing the ammunition, you should replace the leaf spring. By replacing the leaf spring, the power and force of the spring will increase, allowing the hammer to strike with greater force.<\/p>\n\n\n\n Check the revolver’s leaf spring strain screw. If the strain screw is loosened, the firing pin may strike lightly as a result.<\/p>\n\n\n\n Many users of the S&W 617 revolver have encountered timing problems. It is another common problem with the revolver that many people have complained about.<\/p>\n\n\n\n You can check the timing problem by checking the lead build-up in the forcing cone.<\/p>\n\n\n\n Also, if you slowly pull the hammer back, the cylinder latch locks it into place before the hammer is completely back. You can check in this way.<\/p>\n\n\n\n To fix the problem, call Smith & Wesson. They will troubleshoot the problem.<\/p>\n\n\n\n The S&W 617 revolver has a common problem with the hammer becoming jammed. There have been numerous complaints about the issue.<\/p>\n\n\n\n In particular, when using certain ammo, such as Remington and CCI ammo, the revolver’s hammer locks.<\/p>\n\n\n\n It may be due to the bulging of the ammunition after it has been fired. The bulging of the ammunition locks the cylinder closed immediately.<\/p>\n\n\n\n To fix the problem, change your ammunition. If the problem still continues, call Smith & Wesson. They will troubleshoot the problem.<\/p>\n\n\n\n Many users have encountered trigger problems with these 617 revolvers by Smith & Wesson.<\/p>\n\n\n\n The revolver works perfectly in single-action mode, but in double-action mode, it frequently locks up, rendering the trigger useless.<\/p>\n\n\n\n When using rapid fire, the situation gets worse. The cylinder does not move in such a way that the trigger appears to be jammed.<\/p>\n\n\n\n The possible reason may be that dirt may accumulate rapidly under a .22 extractor. If there is dirt underneath that, the cylinder will hang.<\/p>\n\n\n\n To resolve the problem, check the ejector rod’s tightness.<\/p>\n\n\n\n Then, using a toothbrush, remove the dirt from under the extractor at the rear of the cylinder.<\/p>\n\n\n\n Note:<\/em><\/strong> Since oil accumulates dirt, you should not put any oil on a.22 LR revolver, with the possible exception of one drop down the face of the hammer.<\/em><\/p>\n\n\n\n Many users have complained about the canted barrel on their S&W 617 revolver. This indicates that the barrel of their 617 revolvers is slightly over-torqued on one side.<\/p>\n\n\n\n Though this canted barrel is a minor issue, it is undoubtedly the result of quality control issues from Smith & Wesson.<\/p>\n\n\n\n The only possible solution to the problem is to contact Smith & Wesson directly. They will troubleshoot the problem.<\/p>\n\n\n\n Many users have encountered a broken frame issue with the S&W 617 revolver. It results in a lead or burnt powder build-up in the forcing cone.<\/p>\n\n\n\n This may result from the misalignment of the barrel of the revolver. Also, it may occur due to the timing problem of the revolver.<\/p>\n\n\n\n To resolve the issue, call Smith & Wesson. They will replace the damaged frame of your revolver if it is possible to replace it.<\/p>\n\n\n\n![\"Common](\"https:\/\/gunanalyst.com\/wp-content\/uploads\/2022\/09\/Common-Smith-and-Wesson-617-Problems-and-Solutions-1024x536.webp\")
Common Smith and Wesson 617 Problems and Solutions<\/h2>\n\n\n\n
Problems<\/strong><\/td> Solutions<\/strong><\/td><\/tr> Failure to Fire<\/td> Change the ammo. Replace the leaf spring.<\/td><\/tr> Timing Problem<\/td> Call Smith& Wesson.<\/td><\/tr> Locked Hammer Problem<\/td> Change the ammo. Call Smith& Wesson.<\/td><\/tr> Locked Trigger and Cylinder Problem<\/td> Troubleshoot.<\/td><\/tr> Canted Barrel<\/td> Call Smith& Wesson.<\/td><\/tr> Broken Frame<\/td> Call Smith& Wesson.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n 1. Failure to Fire<\/h3>\n\n\n\n
The Fix:<\/h4>\n\n\n\n
2. Timing Problem<\/h3>\n\n\n\n
The Fix: <\/h4>\n\n\n\n
3. Locked Hammer Problem<\/h3>\n\n\n\n
The Fix:<\/h4>\n\n\n\n
4. Locked Trigger and Cylinder Problem<\/h3>\n\n\n\n
The Fix:<\/h4>\n\n\n\n
5. Canted Barrel<\/h3>\n\n\n\n
The Fix:<\/h4>\n\n\n\n
6. Broken Frame<\/h3>\n\n\n\n
The Fix: <\/h4>\n\n\n\n