The solutions to the issues presented will be discussed in this article. A thorough reading of the entire article will provide a clear understanding of Smith & Wesson Model 41 problems<\/strong> and their solutions.<\/p>\n\n\n\n Features & Specifications of Smith and Wesson Model 41:<\/strong><\/p>\n\n\n\n Quick Overview of the Problems and Solutions<\/strong><\/p>\n\n\n\n The Smith & Wesson Model 41 gun has a misfiring problem. This is a problem that many people are having with this particular gun.<\/p>\n\n\n\n This problem might be caused by the use of improper ammunition or a malfunction of the gun itself. Also, the gun’s firing pin may be damaged.<\/p>\n\n\n\n Additionally, it may occur due to a dirty gun and the lack of sufficient lubrication in the gun.<\/p>\n\n\n\n To resolve the problem, thoroughly clean the gun. In addition, the gun must be lubricated every few days.<\/p>\n\n\n\n Switch out your ammunition. People have specifically complained about this problem when using the CCI, Federal, and Remington Golden Bullet.<\/p>\n\n\n\n Winchester ammunition is the best option for preventing the Model 41 gun\u2019s failure to fire.<\/p>\n\n\n\n The Model 41 gun has an issue with its slide. Many times, the slide gets stacked while firing. This do not allow the slide to move forward and chamber the next round.<\/p>\n\n\n\n By removing the barrel assembly, any tension or binding is eliminated, allowing the slide to advance.<\/p>\n\n\n\n In this case, calling Smith & Wesson may be the only option to troubleshoot the issue.<\/p>\n\n\n\n Many users have encountered trigger problems with these Model 41 guns by Smith & Wesson.<\/p>\n\n\n\n If the hammer falls after firing an empty chamber, re-cock the pistol by pulling the slide back is extremely difficult.<\/p>\n\n\n\n The possible reason may be that dirt may accumulate rapidly under a .22 extractor. If there is dirt underneath that, the gun might get locked.<\/p>\n\n\n\n To fix the problem, unload the gun and then pull the trigger. Keep your finger off the trigger while you cycle the slide with your free hand. If cycling is simple, check the disconnector.<\/p>\n\n\n\n Some users have complained about the failure to extract of their Model 41 guns.<\/p>\n\n\n\n The cartridge doesn’t always leave the chamber after being fired. Most of the time, this is caused by a worn extractor, which is the small arm that grabs the case, or a worn case on the cartridge itself.<\/p>\n\n\n\n To solve the issue, examine the extractor carefully. If dirt has developed underneath the extractor, it must be thoroughly cleaned.<\/p>\n\n\n\n It is also recommended that you contact Smith & Wesson directly if your extractor is broken.<\/p>\n\n\n\n Users have reported that their Model 41 guns sometimes begin to stovepipe rather than feed into the chamber of the barrel.<\/p>\n\n\n\n The possible reason for this problem is the use of improper ammunition. Lack of routine maintenance and proper lubrication could also be contributing factors.<\/p>\n\n\n\n To fix the problem, stop using ammo that is incompatible with your Model 41 handgun.<\/p>\n\n\n\n Also, you should switch up your ammunition. Many people have had this problem with Remington Golden Bullets, CCI Clean Bullets, and Federal Bullets, so you should better avoid them.<\/p>\n\n\n\n Additionally, you must ensure that your firearm is lubricated before firing.<\/p>\n\n\n\n Since 1957, Smith & Wesson has manufactured Model 41 firearms. Therefore, many people have been using it for a very long time.<\/p>\n\n\n\n People who own the most up-to-date Model 41 firearm but have to use the older Model 41 magazine have experienced problems with their magazines.<\/p>\n\n\n\n When the slide is open, it is impossible to fully insert older magazines into the gun. To fully insert these magazines, the slide must be closed before inserting the magazine. It makes no difference whether the rounds are loaded or not.<\/p>\n\n\n\n Call Smith & Wesson directly to fix the problem. They will troubleshoot the problem.<\/p>\n\n\n\n The Model 41 was introduced as what Smith & Wesson claimed to be the perfect rimfire target pistol. Users have different thoughts regarding this model.<\/p>\n\n\n\n A user<\/a> stated that his Smith 41 is the most attractive and accurate. The only .22 handgun he ever possessed. It feels excellent in his hand, and shooting is quite gentle.<\/p>\n\n\n\n![\"Common](\"https:\/\/gunanalyst.com\/wp-content\/uploads\/2022\/09\/Common-Smith-and-Wesson-Model-41-Problems-and-Solutions-1024x536.webp\")
Common Smith and Wesson Model 41 Problems and Solutions<\/h2>\n\n\n\n
Problems<\/strong><\/td> Solutions<\/strong><\/td><\/tr> Failure to Fire<\/td> Troubleshoot. Change the ammo.<\/td><\/tr> Slide Lock Problem<\/td> Call Smith & Wesson.<\/td><\/tr> Locked Gun<\/td> Troubleshoot.<\/td><\/tr> Failure to Extract<\/td> Troubleshoot. Call Smith & Wesson.<\/td><\/tr> Failure to Eject<\/td> Change the ammo. Troubleshoot.<\/td><\/tr> Magazine Problem<\/td> Call Smith & Wesson.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n 1. Failure to Fire:<\/h3>\n\n\n\n
The Fix:<\/h4>\n\n\n\n
2. Slide Lock Problem:<\/h3>\n\n\n\n
The Fix: <\/h4>\n\n\n\n
3. Locked Gun:<\/h3>\n\n\n\n
The Fix:<\/h4>\n\n\n\n
4. Failure to Extract:<\/h3>\n\n\n\n
The Fix:<\/h4>\n\n\n\n
5. Failure to Eject:<\/h3>\n\n\n\n
The Fix:<\/h4>\n\n\n\n
6. Magazine Problem:<\/h3>\n\n\n\n
The Fix:<\/h4>\n\n\n\n
User Feedback on Smith and Wesson Model 41<\/h2>\n\n\n\n