After reading this article, you will know the solution to all these problems. You will also know how the users feel about this product. So stay tuned!<\/p>\n\n\n\n
Features & Specifications of Glock 42:<\/strong><\/p>\n\n\n\n A number of feed failures and some stove pipes could happen. To solve this problem, you may require as many as 200 rounds.<\/p>\n\n\n\n About 4-5 magazines can be switched without reaching any solution. Every two rounds, the gun may jam again.<\/p>\n\n\n\n Additionally, after the last round, the slide might not open and the round might not be ejected.<\/p>\n\n\n\n A pistol’s performance can be impacted by limp wristing, a bad grip, and just plain bad pistol shooting technique.<\/p>\n\n\n\n The recoil spring may be too tight or the ammunition is too weak. The ammo such as LCP won’t lock open when using S&B.380 FMJ ammunition for example.<\/p>\n\n\n\n The recoil may too be heavy.<\/p>\n\n\n\n You may want to replace the following parts:<\/p>\n\n\n\n Polishing the feed ramp is one potential remedy. The Glock 42 performs better when using WW\/USA white-box ammunition. Typically, HP is a little hotter.<\/p>\n\n\n\n You’re Glock 42 will cycle and crimping, low loads, max loads, different powders-nothing may work to fix the issue.<\/p>\n\n\n\n Even though some cases are partially ejected and some are not at all, shooting “single action” is smoother.<\/p>\n\n\n\n The weapon must be cocked again after the slides have returned a short distance. It appears as though it would double feed. Because the top round doesn’t load before the second one hits it from below.<\/p>\n\n\n\n Initial reports indicate that it may initially be ammunition sensitive.<\/p>\n\n\n\n It might not function properly with bullets such as the 3.2gr Bullseye 95gr FMJ, PrecisionOne JHP, Hornady CD JHP, Blazer 95gr, Winchester, etc.<\/p>\n\n\n\n Additionally, the recoil spring may not match the ammo. This causes problems.<\/p>\n\n\n\n Always match the recoil spring (poundage) and ammunition. Your RSA# and the ammunition used for the slide must simply get along for the slide to work properly.<\/p>\n\n\n\n Clean and lube the gun properly. Rack the slide a few hundred times to get the gun used to feeding.<\/p>\n\n\n\n Use good ammo such as the Fiocci 95gr. If these don\u2019t work, send the gun to Glock.<\/p>\n\n\n\n Glock 42 MagGuts +1 Magazine Conversion increases the capacity of your 6-round Glock 42. 380 caliber magazine to 7 rounds without extending it.<\/p>\n\n\n\n But the rounds eventually stop feeding into the pipe. The MagGuts mags begin to malfunction.<\/p>\n\n\n\n While there are still rounds in the magazine, the slide could lock open.<\/p>\n\n\n\n Third-party mag extensions or springs like MagGuts in your carry gun or load out are not meant to be. The guns as sophisticated as Glocks don\u2019t like those mags.<\/p>\n\n\n\n They might initially be smooth but will eventually fail.<\/p>\n\n\n\n When you run stock, you can be confident that you’re using a tried-and-true system. A third party cannot always be trusted.<\/p>\n\n\n\n The best thing to do would be to convert your gun to stock entirely. Ditch the MagGuts. They really are a hit or a miss (mostly miss).<\/p>\n\n\n\n Test each mag carefully using the MagGuts conversion. Check to see if you’ve had to file your slide stop if you’re experiencing slide stop issues.<\/p>\n\n\n\n The number of cartridges that FTE is huge, about 20%. This can be attributed to an extractor issue.<\/p>\n\n\n\n It appears that the cartridge is partially removed from the chamber by the ejector. This causes it to occasionally become stuck in the ejection port.<\/p>\n\n\n\n The slight case dimension difference shouldn’t interfere with ejection. This is probably because the Glock 42 chamber dimension is generous.<\/p>\n\n\n\n Stovepipes and erratic ejection are problems with G42 when it is new. It appears that the gun is oversprung and needs some break-in time.<\/p>\n\n\n\n Strip it, clean it very carefully and properly. And then lube it. After doing the basics, take it to the range and shoot it.<\/p>\n\n\n\n This is a common problem and you need to give the gun a break-in time. Also, use different kinds of ammo with different mags. Shoot for a while at the rage with different ammo.<\/p>\n\n\n\n If this doesn\u2019t work, send the gun back to Glock. There may be extractor defects (e.g the spring) that they will fix.<\/p>\n\n\n\n The G42 is a fine handgun but not for everyone. Your grip is going to dictate most of your love for this gun. Because the magazine catch button can be a nuance for you.<\/p>\n\n\n\n In terms of the 42, Hornady ammunition is the standard for EDC. That is how it was preferred by many users.<\/p>\n\n\n\n Some people firmly believe that G42 has no recoil! A mag may be fired at a target in record time! And that is often the truth!<\/p>\n\n\n\n For its tiny size, it is very accurate, which is nearly astounding. The gun is a yummy size, and shooting them is easy. However, they are too unreliable to carry.<\/p>\n\n\n\n It regularly experiences problems, flat-nosed bullets for example. It’s still a fairly manageable little rifle, though. Probably the reason why having one adds a little more to one’s manhood, as stated by many! (just channeling that run-of-the-mill sexist neighbor).<\/p>\n\n\n\n From what I see, users say as many bad things as they say good things about G42.<\/p>\n<\/div><\/div>\n\n\n\nBarrel Length<\/strong><\/td> 82,5 mm<\/td><\/tr> Magazine Capacity<\/strong><\/td> Standard: 6<\/td><\/tr> Overall Length<\/strong><\/td> 151 mm<\/td><\/tr> Caliber<\/strong><\/td> 380 Auto<\/td><\/tr> Twist Rate<\/strong><\/td> 1:9.84 inches<\/td><\/tr> Sight<\/strong><\/td> standard Glock plastic sight fillers<\/td><\/tr> Safety<\/strong><\/td> Safe Action System<\/td><\/tr> Dimensions <\/strong><\/td> Width (Overall): 25 Mm Height Incl. Mag.: 105 Mm<\/td><\/tr> Weight<\/strong><\/td> With empty magazine: 390 g<\/td><\/tr> Trigger Pull<\/strong><\/td> 24 N (depending on the configuration).<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n ![\"Common](\"https:\/\/gunanalyst.com\/wp-content\/uploads\/2022\/09\/Common-Glock-42-Problems-and-Solutions-1024x536.webp\")
Common Glock 42 Problems and Solutions<\/h2>\n\n\n\n
Problems<\/strong><\/td> Solutions<\/strong><\/td><\/tr> Feed Problems<\/td> Replace several parts and change ammo.<\/td><\/tr> Cycling Problems<\/td> Change Ammo and make sure RSA matches with ammo.<\/td><\/tr> MagGuts Problem<\/td> Ditch the MagGuts. Switch to stock configuration.<\/td><\/tr> Extractor Problem<\/td> Clean and lube the gun. Dry fire.<\/td><\/tr> Magazine Issues<\/td> Change magazine. Experiment till you find the right one.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n Feed Problems<\/h3>\n\n\n\n
Possible Reasons<\/h4>\n\n\n\n
The Fix<\/h4>\n\n\n\n
Cycling Problems<\/h3>\n\n\n\n
Possible Reasons<\/h4>\n\n\n\n
The Fix<\/h4>\n\n\n\n
MagGuts Problem<\/h3>\n\n\n\n
Possible Reasons<\/h4>\n\n\n\n
The Fix<\/h4>\n\n\n\n
Extractor Problem<\/h3>\n\n\n\n
Possible Reasons<\/h4>\n\n\n\n
The Fix<\/h4>\n\n\n\n
User Feedback on Glock 42<\/h2>\n\n\n\n