video on YouTube<\/a>.<\/p>\n\n\n\n2. Trigger Reset Issue:<\/h3>\n\n\n\n
It is an issue where the trigger does not go in place to be pulled for the next shot. It lays backward until it is manually pushed to its place.<\/p>\n\n\n\n
Possible Reasons<\/h4>\n\n\n\n
Essentially, the region behind the trigger bar had to be kept clean, and the trigger bar’s angle had to be maintained. If someone forces the slide off while the trigger bar is not in the proper position, that angle can be adjusted.<\/p>\n\n\n\n
The Ejector has a path that the Trigger Bar follows, and the Trigger Bar can only operate when the Ejector is up and a Magazine is in position. If some of the holes in the ejector aren’t lined up correctly, it may have trouble resetting.<\/p>\n\n\n\n
The Fix:<\/h4>\n\n\n\n
Replacing the whole trigger group and trigger disconnect bar would certainly cure the problem if the problem lies in them.<\/p>\n\n\n\n
To prevent this issue you should make sure that the gun is regularly cleaned. Especially, the region behind the trigger bar should get extra attention.<\/p>\n\n\n\n
3. Jamming:<\/h3>\n\n\n\n
Jamming is a frequent issue with Ruger SR9c. Therefore, you had better be ready to handle it.<\/p>\n\n\n\n
Possible Reasons<\/h4>\n\n\n\n
Dirt, debris, a mechanical issue, or anything else could be the cause. As a result, it is very challenging to identify a single point of failure.<\/p>\n\n\n\n
However, limp wristing or a malfunctioning extractor are typically the two main causes of jams in this gun.<\/p>\n\n\n\n
Limp wristing happens when the shooter’s grip is insufficiently firm and the wrist is not held rigidly and straightly enough to prevent the firearm’s frame from recoiling as the bolt or slide cycles on a pistol.<\/p>\n\n\n\n
The Fix:<\/h4>\n\n\n\n
Shooters are more likely to limp their wrists if they “teacup” with their support hand, holding the bottom of the handle rather than the grip and frame of the handgun.<\/p>\n\n\n\n
Take hold of the pistol firmly with both hands. The foundation for your shooting should be your upper body, not your hands and wrists.<\/p>\n\n\n\n
If jamming persists after that, the extractor is probably the source of the issue. The extractor should be replaced to fix the problem.<\/p>\n\n\n\n
Nevertheless, there is a good likelihood that the problem will persist. Send the weapon to Ruger for repair in this situation.<\/p>\n\n\n\n
When the slide or bolt moves backward, but the empty cartridge case stays in the chamber, this is referred to as failure to extract.<\/p>\n\n\n\n
Possible Reasons<\/h4>\n\n\n\n
This can be caused by a filthy chamber, a damaged extractor claw, case rim failures, or a variety of other factors.<\/p>\n\n\n\n
Failure to extract is frequently caused by low quality or broken magazines, weak magazine springs, or shooters who do not keep a firm hold on the rifle or ride the slide forward as it travels.<\/p>\n\n\n\n
The Fix:<\/h4>\n\n\n\n
The SR series centerfire pistols are extremely easy to limp wrist. To keep the gun working, you must maintain your arm completely rigid.<\/p>\n\n\n\n
The strong recoil springs absorb so much of the recoil that it’s simple to “assist them along a bit” by allowing your arm to absorb enough of the recoil that the slide doesn’t cycle correctly.<\/p>\n\n\n\n
If the problem persists, you will need to replace the recoil spring.<\/p>\n\n\n\n
5. Stovepiping:<\/h3>\n\n\n\n
A failure to expel is essentially what is meant by a “stovepipe.” It is a special instance of ejection failure.<\/p>\n\n\n\n
Possible Reasons<\/h4>\n\n\n\n
If the case became entangled in the filthy chamber, allowing the extractor to slide will cause the bullet stovepiping. It might be caused by a faulty extractor spring or by flaws in the bullet case.<\/p>\n\n\n\n
The most prevalent problem, though, is a weak grasp, sometimes known as “limp-wristing.”<\/p>\n\n\n\n
The Fix:<\/h4>\n\n\n\n
Here’s a tried-and-true method: Tap, Rack, and Assess. Tap the bottom of your magazine hard to ensure it’s properly seated; rack the slide to the rear to feed a new round into the chamber, and evaluate downrange.<\/p>\n\n\n\n
Stovepipes can be avoided with proper grip and maintenance.<\/p>\n\n\n\n
Keeping your gun clean and oiled is the standard treatment for many stovepipe difficulties that aren’t caused by a shooter’s technique.<\/p>\n\n\n\n
Less frequently, it is the ammunition that creates a stovepipe, with handloads being the most common problem.<\/p>\n\n\n\n
![\"Common](\"https:\/\/gunanalyst.com\/wp-content\/uploads\/2022\/08\/Common-Ruger-sr9c-Problems-and-Solutions-1024x536.webp\")