{"id":1528,"date":"2022-08-31T20:12:19","date_gmt":"2022-08-31T20:12:19","guid":{"rendered":"https:\/\/gunanalyst.com\/?p=1528"},"modified":"2023-11-27T00:29:21","modified_gmt":"2023-11-27T00:29:21","slug":"ruger-wrangler-problems","status":"publish","type":"post","link":"https:\/\/gunanalyst.com\/ruger-wrangler-problems\/","title":{"rendered":"6 Ruger Wrangler Problems You Probably Didn\u2019t Know Before"},"content":{"rendered":"\n

A cowboy-action pistol within your budget is like a dream come true. But such guns come with some issues. That is why you should know the Ruger Wrangler problems before rushing into a decision.<\/p>\n\n\n\n

Among all complaints I have seen and heard about a Wrangler, the most common ones are regarding jamming, transfer bar, accuracy, hammer not cocking, stuck cylinder, and poor timing.<\/strong><\/p>\n\n\n\n

Reading this article, you will also get to know about the probable causes and solutions. So, let\u2019s get started by knowing the specs first.<\/p>\n\n\n\n

<\/p>\n\n\n\n\n\n

Features & Specifications of Ruger Wrangler:<\/strong><\/p>\n\n\n\n

Barrel Length<\/strong><\/td>4.62″<\/td><\/tr>
Magazine Capacity<\/strong><\/td>6 rounds<\/td><\/tr>
Overall Length<\/strong><\/td>10.25″<\/td><\/tr>
Caliber<\/strong><\/td>22 LR<\/td><\/tr>
Twist Rate<\/strong><\/td>1:14″ RH<\/td><\/tr>
Rear Sight<\/strong><\/td>Integral<\/td><\/tr>
Front Sight<\/strong><\/td>Blade<\/td><\/tr>
Safety<\/strong><\/td>Transfer bar mechanism and loading gate interlock<\/td><\/tr>
Weight<\/strong><\/td>30 oz.<\/td><\/tr>
Trigger Pull<\/strong><\/td>4 lbs. 8 oz.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n
\"Common
Ruger Wrangler Problems<\/figcaption><\/figure>\n\n\n\n

Common Ruger Wrangler Problems and Solutions<\/h2>\n\n\n\n
Problems<\/strong><\/td>Solutions<\/strong><\/td><\/tr>
Jamming<\/td>Check the center pin along with its spring, tighten the latch, or send it to Ruger.<\/td><\/tr>
Transfer Bar<\/td>Push the transfer bar all the way, or take expert help.<\/td><\/tr>
Accuracy<\/td>Correct the sights, or install aftermarket sights. And, don\u2019t drop the gun.<\/td><\/tr>
Hammer not Cocking<\/td>Replace the cylinder pin, or take the gun to a local gunsmith.<\/td><\/tr>
Cylinder Stuck<\/td>Try different ammo, or replace the faulty firing pin.<\/td><\/tr>
Bad Timing<\/td>Contact Ruger for help.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

1. Jamming Issue<\/h3>\n\n\n\n

A particular jamming problem occurs in some Wrangler units when it is held at any downwards angle.<\/p>\n\n\n\n

Possible Reasons<\/h4>\n\n\n\n

A faulty or misaligned center pin can cause this problem. A properly seated center pin can solve the issue quickly.<\/p>\n\n\n\n

Also, a latch that is not tightened properly does not engage fully and causes this issue.<\/p>\n\n\n\n

The Fix<\/h4>\n\n\n\n

From the reasons, you can guess the solution.<\/p>\n\n\n\n

First of all, disassemble your Wrangler, and check whether the center pin is seated properly and functioning smoothly.<\/p>\n\n\n\n

Otherwise, find the faulty part, and replace it. Here, the spring that holds the center pin in its place can be faulty too.<\/p>\n\n\n\n

After that, check whether the latch is fully tightened or not.<\/p>\n\n\n\n

In case this problem occurs in new units, it would be better to contact Ruger for the solution.<\/p>\n\n\n\n

2.  Transfer Bar Problem<\/h3>\n\n\n\n

While cocking a Wrangler, tilting can hang up the transfer bar on the bottom of the firing pin.<\/p>\n\n\n\n

Possible Reasons<\/h4>\n\n\n\n

The plunger is responsible for keeping the transfer bar away from the firing pin while cycling the action.<\/p>\n\n\n\n

So, a faulty spring-loaded plunger can cause this problem. You should take out the cylinder base pin and examine for any irregularities.<\/p>\n\n\n\n

The Fix<\/h4>\n\n\n\n

As I don\u2019t know the severity of the Ruger Wrangler transfer bar problem you are facing, I can start by giving a simpler solution.<\/p>\n\n\n\n

Try pushing the transfer bar all the way in when the gun is fully cocked. It should do the trick. Otherwise, follow other solutions.<\/p>\n\n\n\n

The disassembly and careful inspection are too complex for many users. If you are among them, it will be better to take the help of a gunsmith.<\/p>\n\n\n\n

Another fix you can try before taking expert help is by using different ammunition of various brands and velocities.<\/p>\n\n\n\n

3. Accuracy Problem<\/h3>\n\n\n\n

Not many but a few users complain that their Wranglers shoot 3 levels high and 3 levels left from the target at a distance of 25 yards.<\/p>\n\n\n\n

Possible Reasons<\/h4>\n\n\n\n

Not all units of Ruger Wrangler have accuracy problems. In most cases, it seems that the fixed sight is the reason for poor target groups.<\/p>\n\n\n\n

Besides manufacturing faults (regarding fixed sights), dropping the gun and making the sights misaligned are also very common.<\/p>\n\n\n\n

The Fix<\/h4>\n\n\n\n

From the nature of the problem and cause, I think that taking the gun to a gunsmith is the primary solution.<\/p>\n\n\n\n

The task here is to align and calibrate the sights properly. Or, you can simply install third-party sights<\/strong><\/a> and ditch the faulty stock sights.<\/p>\n\n\n\n

Lastly, you should handle your Wrangler carefully. If it takes a beating or drops on hard surfaces, you will surely face an accuracy issue.<\/p>\n\n\n\n

4. Hammer Doesn\u2019t Cock<\/h3>\n\n\n\n

In this particular problem, you will notice that the hammer is not going to the full cock position if the barrel is pointed downwards.<\/p>\n\n\n\n

Possible Reasons<\/h4>\n\n\n\n

Due to a Ruger Wrangler cylinder pin problem, you can face such situations. But there are other reasons to consider too.<\/p>\n\n\n\n

Carefully look at the fitting of the base pin to the latch. Due to misalignment, the base pin latch may not engage the base pin groove properly.<\/p>\n\n\n\n

The Fix<\/h4>\n\n\n\n

There is no other way than to disassemble the gun if you want to find out the faulty component that is causing this issue.<\/p>\n\n\n\n

After a thorough inspection, you may notice that the cylinder pin has become faulty. Replacing it with a new one should fix the problem.<\/p>\n\n\n\n

But the second reason is much more complex to deal with.<\/p>\n\n\n\n

I recommend you visit a gunsmith or send the gun to Ruger for fixing the base pin to latch fitment.<\/p>\n\n\n\n

5. Cylinder Stuck Problem<\/h3>\n\n\n\n

For some reason, a loaded Wrangler cylinder may get stuck due to excessive drag.<\/p>\n\n\n\n

Possible Reasons<\/h4>\n\n\n\n

You can also call this a Ruger Wrangler firing pin problem because a worn-out pin causes this issue.<\/p>\n\n\n\n

If the cylinder is too stiff, you will also have to check the ammo you are using.<\/p>\n\n\n\n

The Fix<\/h4>\n\n\n\n

Before disassembling the gun, and looking for any faulty parts, you should try changing the ammo brand.<\/p>\n\n\n\n

It is the easiest thing to do first in this problem.<\/p>\n\n\n\n

Then, take out the firing pin and see whether it has any irregularities. Check out this link<\/strong><\/a> for replacing the faulty pin.<\/p>\n\n\n\n

On rare occasions, dry firing solved some of the users\u2019 problems with the firing pin. You can give it a try too.<\/p>\n\n\n\n

However, don\u2019t fire fry too many times because it can damage certain components.<\/p>\n\n\n\n

6. Timing Problem<\/h3>\n\n\n\n

Slow cocking the hammer of a Wrangler leads to firing without the cylinder being properly aligned.<\/p>\n\n\n\n

Possible Reasons<\/h4>\n\n\n\n

From the nature of the problem, you can understand that fast cocking can solve the issue almost immediately.<\/p>\n\n\n\n

But this should not be the case because the gun should reliably operate at slow actions too. <\/p>\n\n\n\n

The Fix<\/h4>\n\n\n\n

From the discussion, it is clear that the timing issue with Wranglers is not common.<\/p>\n\n\n\n

Giving solutions to such unique problems is not easy.<\/p>\n\n\n\n

Instead of doing trials and errors to fix it, you should contact Ruger, explain the situation and seek help.<\/p>\n\n\n\n

\n

User Feedback on Ruger Wrangler<\/h2>\n\n\n\n

In my opinion, Ruger Wrangler is a durable and reliable pistol. Indeed, it has lots of issues but there are no other reliable competitor models at this price. Let\u2019s see what the users think about this firearm.<\/p>\n\n\n\n

Wrangler is a good serviceable plinker<\/a> available at hard-to-beat pricing. Most of the units don\u2019t give users hard times even after shooting 600 rounds.<\/p>\n\n\n\n

For beginners, Wrangler is a good gun. According to the users<\/strong><\/a>, saving up while learning how to shoot with Ruger Wranglers and buying an expensive one later is a good strategy.<\/p>\n\n\n\n

Due to cheap build quality<\/strong><\/a>, Wrangler doesn\u2019t qualify to be a primary firearm. You must rely on a solid revolver for emergencies.<\/p>\n<\/div><\/div>\n\n\n\n

\n