{"id":1493,"date":"2022-08-30T19:00:56","date_gmt":"2022-08-30T19:00:56","guid":{"rendered":"https:\/\/gunanalyst.com\/?p=1493"},"modified":"2022-08-30T19:00:58","modified_gmt":"2022-08-30T19:00:58","slug":"ruger-lcr-38-special-problems","status":"publish","type":"post","link":"https:\/\/gunanalyst.com\/ruger-lcr-38-special-problems\/","title":{"rendered":"Ruger LCR 38 Special Problems You Can\u2019t Avoid"},"content":{"rendered":"\n

For being one of the lightest in its class, and compact, Ruger had to make some compromises in this LCR variant. Hence, there are a few Ruger LCR 38 Special problems that you should know.<\/p>\n\n\n\n

These minor issues are regarding cylinder and trigger. And, there are not many complaints.  <\/strong><\/p>\n\n\n\n

For your convenience, I have included the possible reasons for those problems and solutions. To get a complete overview, don\u2019t skip any part of this article. <\/p>\n\n\n\n

Features & Specifications of Ruger LCR 38 Special:<\/strong><\/p>\n\n\n\n

Barrel Length<\/strong><\/td>1.87″<\/td><\/tr>
Magazine Capacity<\/strong><\/td>5 rounds<\/td><\/tr>
Overall Length<\/strong><\/td>6.50″<\/td><\/tr>
Caliber<\/strong><\/td>38 SPL +P<\/td><\/tr>
Twist Rate<\/strong><\/td>1:16″ RH<\/td><\/tr>
Rear Sight<\/strong><\/td>U-Notch Integral<\/td><\/tr>
Front Sight<\/strong><\/td>Replaceable, Pinned Ramp<\/td><\/tr>
Safety<\/strong><\/td>Transfer Bar<\/td><\/tr>
Dimensions <\/strong><\/td>4.50″ H<\/td><\/tr>
Weight<\/strong><\/td>13.5 oz.<\/td><\/tr>
Trigger Pull<\/strong><\/td>7 lbs.  8 ounces<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n
\n
\"Common
Ruger LCR 38 Special Problems<\/figcaption><\/figure><\/div>\n\n\n

Common Ruger LCR 38 Special Problems and Solutions<\/h2>\n\n\n\n

The following table has a summary of all the problems and their respective solutions. Let\u2019s have a look.<\/p>\n\n\n\n

Quick Overview of the Problems and Solutions<\/strong><\/p>\n\n\n\n

Problems<\/strong><\/td>Solutions<\/strong><\/td><\/tr>
Cylinder Problem<\/td>Replace the plunger and cylinder stop spring.<\/td><\/tr>
Stuck\/Frozen Trigger<\/td>Clean the gun properly, and replace the trigger pin or spring as necessary.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

1. Cylinder Problems<\/h3>\n\n\n\n

In this problem, you may notice that the cylinder is not locking properly, and it spins freely passing every chamber.<\/p>\n\n\n\n

Possible Reasons<\/h4>\n\n\n\n

It is hard to suspect the cause without inspecting the gun physically.<\/p>\n\n\n\n

If you ask me, I will tell you to inspect the condition of the cylinder stop spring and plunger.<\/p>\n\n\n\n

The Fix<\/h4>\n\n\n\n

To solve this problem, you have to disassemble the firearm partially and access the plunger as well as the cylinder stop spring.<\/p>\n\n\n\n

In this YouTube video<\/strong><\/a>, you can see a proper replacement procedure. But the gun model is Taurus Ultra Lite in the video.<\/p>\n\n\n\n

All you have to do is read the owner manual of the LCR 38 special, and disassemble the gun accordingly.<\/p>\n\n\n\n

Those who are still facing the same issue ever after replacing the plunger and the spring should contact Ruger for help.<\/p>\n\n\n\n

2. Stuck\/Frozen Trigger<\/h3>\n\n\n\n

The trigger of an LCR 38 Special can get frozen all of a sudden in the middle of a shootout.<\/p>\n\n\n\n

Possible Reasons<\/h4>\n\n\n\n

Too much stiffness or stuck trigger problem can occur due to dust buildup. Also, oil or packaging grease can prevent it from resetting after firing a round.<\/p>\n\n\n\n

You may think that oil is bad but on the contrary. Certain locations need to be lubricated for proper actions.<\/p>\n\n\n\n

Check out the trigger pin for any kind of deformation.<\/p>\n\n\n\n

Also, inspect the spring that helps the trigger reset. A weak spring often causes this problem on LCR 38 Special revolvers.<\/p>\n\n\n\n

The Fix<\/h4>\n\n\n\n

For proper cleaning, taking the gun to a gunsmith is a better option. But those who want to do it by themselves can follow the steps below.<\/p>\n\n\n\n