I will give you the solution to these common issues in this article. Additionally, you will get authentic reviews from users as well. So, stay tuned!<\/p>\n\n\n\n
Features & Specifications of Glock 30S:<\/strong><\/p>\n\n\n\n One or two jams of the fail-to-feed variety per 200 rounds are the issue. The bullet appears to be trying to enter the chamber but is being blocked by the mouth since it is pointing upward.<\/p>\n\n\n It is known as a “bolt over base” failure when the slide catches the extraction groove. So, the magazine doesn’t get the next round into position in time. This results in the nose up jam of the bullet.<\/p>\n\n\n\n An “extra power” recoil spring can also cause it if you go overboard by making the slide outrun the magazine spring.<\/p>\n\n\n\n Examine the magazine for FOD that hinders the smooth and rapid movement of the round stack. Also check feed lips that are too widely open, burrs or flash on the follower, or weak magazine springs. Replace the spring and polish the burrs when necessary.<\/p>\n\n\n\n The problem starts after around 20 rounds of the magazine have been used. The shell is left in the chamber keeping the next shell from loading. The shell rests angled up.<\/p>\n\n\n\n After 126 rounds, there should be an expected buildup on the extractor. The case mouth edge of the top\/first round in the magazine may be caught on the bottom edge of the rim of the case as it is being withdrawn.<\/p>\n\n\n\n The issue might get “worse” or “better” based on how much the case mouth’s edge protrudes away from the bullet.<\/p>\n\n\n\n This could account for why how it “feels” changes periodically. It might be impacted by various ammunition kinds, brands, or even changes in how bullets seat or crimp inside a single box of ammunition.<\/strong><\/p>\n\n\n\n Fix the buildup by polishing and or cleaning the gun. Make sure you lubricated the gun after polishing. The case mouth protrusion can be fixed under the supervision of an expert gunsmith by reducing the protrusion.<\/p>\n\n\n\n The slide would not stay locked back while adding a magazine, loaded or unloaded when it is in the slide lock position. The slide would move quickly and even fire a shot from a filled magazine.<\/p>\n\n\n\n Upon a forceful mag insertion, many Glocks will almost instantly drop a slide. For Glocks, this might be regarded as typical.<\/p>\n\n\n\n A bad slide stop spring may also cause this issue. Moreover, change of any factory parts does it as well!<\/p>\n\n\n\n If you don’t like the drop slide, you can prevent the slide from “dropping” by inserting the magazine smoothly while using strong pressure as opposed to smashing it into the grip. Try the pistol with factory ammo and barrel.<\/p>\n\n\n\n Ensure that the mag assembly only contains the base plate, the mag insert, and the appropriate stock spring and follower. Install the Glock slide stop spring to prevent slide stop problems if these don\u2019t work. This video<\/a> can help with that.<\/p>\n\n\n\n The round’s nose will occasionally go up and become stuck at the top of the feed ramp. Usually, it occurs on the final one or two rounds in the magazine.<\/p>\n\n\n\n The likely culprit is the Glock 30S frame. To determine where the problem still exists, switch the entire uppers between the two frames.<\/p>\n\n\n\n If you can find a conventional Glock 30 frame, drop your 30SF slide on it, and it will function like a bullet hose.<\/p>\n\n\n\n Get a new Gen 3 Glock 30 frame if you don’t care about the serial numbers not matching. It is a non- SF frame.<\/p>\n\n\n\n New 30S trigger is more difficult to pull and feels like a brick wall. Even after thoroughly cleaning and polishing the weapon, the results will be awful.<\/p>\n\n\n\n A drag could be caused by the trigger spring being hung on one side. Otherwise, the heavier spring on the rifle could be problematic.<\/p>\n\n\n\n The bump they put to the Gen 4 trigger bars is to blame for the failure to return to the battery issue.<\/p>\n\n\n\n Disassemble the pistol completely, then use a Dremel to clean the connector and every other trigger component. See if this fixes the problem.<\/p>\n\n\n\n Or let everything lap in by shooting the Glock 30S. You may also install the Glock OEM 4.5 lb connector and swap out the serrated trigger for a smooth OEM version. Put in a Gen 3 trigger bar replacing a Gen 4 one.<\/p>\n\n\n\nBarrel Length<\/strong><\/td> 3.77 inches<\/td><\/tr> Magazine Capacity<\/strong><\/td> Standard: 10 Optional: 9 \/ 13<\/td><\/tr> Overall Length<\/strong><\/td> 6.96 inches<\/td><\/tr> Caliber<\/strong><\/td> .45 ACP<\/td><\/tr> Twist Rate<\/strong><\/td> 400 mm \/ 15.75 in<\/td><\/tr> Sights<\/strong><\/td> Polymer \u201cU\u201d dot configuration (Trijicon).<\/td><\/tr> Safety<\/strong><\/td> Striker-fired operating system: Safe Action<\/td><\/tr> Weight<\/strong><\/td> With loaded magazine 855 g Without magazine 575 g<\/td><\/tr> Trigger Pull<\/strong><\/td> 28 N<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n ![\"Glock](\"https:\/\/gunanalyst.com\/wp-content\/uploads\/2022\/08\/Glock-30s-Problems-and-Solutions-1024x536.webp\")
Common Glock 30s Problems and Solutions<\/h2>\n\n\n\n
Problems<\/strong><\/td> Solutions<\/strong><\/td><\/tr> Failure to Feed<\/strong><\/td> Troubleshoot the bolt over base failure and RSA.<\/td><\/tr> Failure to Extract<\/strong><\/td> Troubleshoot RSA.<\/td><\/tr> Slide Lock Issues<\/strong><\/td> Troubleshoot or replace slide stop spring.<\/td><\/tr> Jamming at Feed Ramp<\/strong><\/td> Change 30SF frame.<\/td><\/tr> Trigger and Trigger Bar Issues<\/strong><\/td> Troubleshoot or replace with Gen 3 trigger.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n 1. Failure to Feed:<\/h3>\n\n\n\n
![\"the](\"https:\/\/gunanalyst.com\/wp-content\/uploads\/2022\/08\/image.webp\")
Possible Reasons<\/h4>\n\n\n\n
The Fix<\/h4>\n\n\n\n
2. Failure to Extract:<\/h3>\n\n\n\n
Possible Reasons<\/h4>\n\n\n\n
The Fix<\/h4>\n\n\n\n
3. Slide Lock Issues: <\/h3>\n\n\n\n
Possible Reasons<\/h4>\n\n\n\n
The Fix<\/h4>\n\n\n\n
4. Jamming at Feed Ramp:<\/h3>\n\n\n\n
Possible Reasons<\/h4>\n\n\n\n
The Fix<\/h4>\n\n\n\n
5. Trigger and Trigger Bar Issues:<\/h3>\n\n\n\n
Possible Reasons<\/h4>\n\n\n\n
The Fix<\/h4>\n\n\n\n